Ten reasons or cause LED driver to fail

Basically, the main function of the LED driver is to convert the input AC voltage source into a current source whose output voltage can vary with the forward voltage drop of the LED Vf.

As a key component in LED lighting, the quality of the LED driver directly affects the reliability and stability of the overall luminaire. Based on LED driver and other related technologies and customer application experience, this paper analyzes and analyzes many failures in lamp design and application:

1. The range of variation of LED lamp bead Vf is not considered, resulting in low efficiency of the lamp and even unstable operation.

The load end of the LED luminaire is generally composed of a number of LEDs connected in series and parallel, and its working voltage is Vo=Vf*Ns, where Ns represents the number of LEDs connected in series. The Vf of the LED fluctuates with temperature. In general, at a constant current, Vf becomes low at high temperatures, and Vf becomes high at low temperatures. Therefore, the LED lamp load voltage corresponds to VoL at high temperature, and the LED lamp load voltage corresponds to VoH at low temperature. When selecting an LED driver, consider that the driver output voltage range is greater than VoL~VoH.

If the maximum output voltage of the selected LED driver is lower than VoH, the maximum power of the luminaire may not reach the actual power required at low temperature. If the lowest voltage of the selected LED driver is higher than VoL, the driver output may exceed the working range at high temperature. Unstable, the lamp will flash and so on.

However, considering the overall cost and efficiency considerations, it is impossible to blindly pursue the ultra-wide output voltage range of the LED driver: since the driver voltage is only in a certain interval, the driver efficiency is the highest. After the range is exceeded, the efficiency and power factor (PF) will be worse. At the same time, the output voltage range of the driver is too wide, which leads to cost increase and efficiency cannot be optimized.

2. Power reserve and derating requirements are not considered

In general, the nominal power of an LED driver is the measured data at rated ambient and rated voltage. Considering that different customers have different applications, most LED driver suppliers will provide power derating curves (common load vs ambient temperature derating curves and load vs. input voltage derating curves) on their own product specifications.

As shown in Figure 1, the red curve shows the power derating curve of the LED driver's load as a function of ambient temperature at 120Vac input. When the ambient temperature is below 50 °C, the drive allows 100% full load. When the ambient temperature is up to 70 °C, the drive can only derate to 60% load. When the ambient temperature changes between 50-70 °C, the drive load will follow. The temperature rises and decreases linearly.

The blue curve shows the power derating curve of the LED driver's load as a function of ambient temperature at 230Vac or 277Vac input. The principle is similar.

As shown in Figure 2, the blue curve shows the derating curve of the LED driver's output power as a function of input voltage at an ambient temperature of 55 °C. When the input voltage is 140Vac, the load of the driver allows 100% full load, and the input voltage is lowered. If the output power is constant, the input current will rise, resulting in increased input loss, lower efficiency, higher device temperature, and individual temperature points. May exceed the standard and may even cause device failure.

Therefore, as shown in Figure 2, when the input voltage is less than 140Vac, the output load of the driver is required to decrease linearly as the input voltage decreases. After understanding the derating curve and the corresponding requirements, the LED driver should be considered and selected according to the actual ambient temperature and input voltage, and the derating margin should be appropriately set.

3, do not understand the working characteristics of LED

Some customers have requested that the input power of the lamp be a fixed value, fixed by 5% error, and the output current can only be adjusted to the specified power for each lamp. Due to different working environment temperatures and lighting times, the power of each lamp will vary greatly.

Customers make such requests, despite their marketing and business factor considerations. However, the volt-ampere characteristics of the LED determine the LED driver as a constant current source, and its output voltage varies with the LED load series voltage Vo. The input power varies with Vo when the overall efficiency of the driver is substantially constant.

At the same time, the overall efficiency of the LED driver will increase after thermal balance. Under the same output power, the input power will decrease compared to the startup time.

Therefore, when the LED driver application needs to formulate the requirements, it should first understand the working characteristics of the LED, avoid introducing some indicators that do not conform to the principle of the working characteristics, and avoid the indicators far exceeding the actual demand, and avoid excessive quality and waste of cost.

4, failure in the test

There have been customers who have purchased many brands of LED drivers, but all samples failed during the test. Later, after on-site analysis, the customer used the self-internal voltage regulator to directly supply power to the LED driver. After power-on, the regulator was gradually adjusted from 0Vac to the rated operating voltage of the LED driver.

Such a test operation makes it easy for the LED driver to start up and load at a small input voltage, which causes the input current to be much larger than the rated value, and internal input related devices such as fuses, rectifier bridges, The thermistor and the like fail due to excessive current or overheating, causing the drive to fail.

Therefore, the correct test method is to adjust the voltage regulator to the rated operating voltage range of the LED driver, and then connect the driver to the power-on test.

Of course, technically improving the design can also avoid the failure caused by such test misoperation: setting the startup voltage limiting circuit and the input undervoltage protection circuit at the input of the driver. When the input does not reach the startup voltage set by the driver, the driver does not work; when the input voltage drops to the input undervoltage protection point, the driver enters the protection state.

Therefore, even if the self-recommended regulator operation steps are still used during the customer test, the drive has self-protection function and does not fail. However, customers must carefully understand whether the LED driver products purchased have this protection function before testing (taking into account the actual application environment of LED drivers, most LED drivers do not have this protection function).

5, different loads, different test results

When the LED driver is tested with an LED lamp, the result is normal. When the test is carried out with an electronic load, the result may be abnormal. Usually this phenomenon has the following reasons:

(1) The instantaneous voltage or power of the output of the driver exceeds the working range of the electronic load meter. (especially in CV mode, the maximum test power should not exceed 70% of the maximum load power, otherwise the load may be over-power protected during loading, causing the drive to not work or load.)

(2) The characteristics of the electronic load meter used are not suitable for measuring the constant current source, and the load voltage position jump occurs, resulting in the drive not working or loading.

(3) Because the input of the electronic load meter will have a large internal capacitance, the test is equivalent to a large capacitor connected in parallel with the output of the driver, which may cause unstable current sampling of the driver.

Because the LED driver is designed to meet the operating characteristics of LED luminaires, the closest test to actual and real-world applications should be to use LED bead as the load, string on the ammeter and voltmeter to test.

6. The following conditions that often occur can cause damage to the LED driver :

(1) The AC is connected to the DC output of the driver, causing the drive to fail;

(2) The AC is connected to the input or output of the DC/DC driver, causing the drive to fail;

(3) The constant current output terminal is connected with the modulating light, which causes the driver to fail;

(4) The phase line is connected to the ground line, resulting in no output of the driver and charging of the outer casing;

7, the phase line is wrong

Generally, the outdoor engineering application is a 3-phase four-wire system. Taking the national standard as an example, the rated working voltage between each phase line and the neutral line is 220Vac, and the voltage between the phase line and the phase line is 380Vac. If the construction worker connects the input of the drive to the two phase lines, the power input to the LED driver exceeds the standard and the product fails.

As shown in the figure above, V1 represents the first phase voltage, V2 represents the second phase voltage, and R1 and R2 represent the LED drivers normally installed in the line. When the neutral line (N) on the line is disconnected, the drivers R1 and R2 on the two branches are connected to the 380Vac voltage in series. Because of the difference in input internal resistance, when one of the drivers is charged to start, the internal resistance becomes small, and the voltage may be mostly applied to the other driver, causing its overvoltage damage to fail.

Therefore, it is recommended that the switch or circuit breaker be broken together on the same distribution branch, and it is not possible to disconnect only the neutral line. Do not place the distribution fuse on the neutral line. Avoid contact with the neutral line on the line.

8, the grid fluctuation range is beyond the reasonable range

When the wiring of the same transformer grid branch is too long and there are large power equipment in the branch, when the large equipment starts and stops, the grid voltage will fluctuate drastically, and even the grid will be unstable. When the instantaneous voltage of the power grid exceeds 310Vac, the drive may be damaged (even if there is a lightning protection device, because the lightning protection device is dealing with pulse spikes of several tens of uS levels, and the power grid fluctuation may reach several tens of mS or even several hundred mS).

Therefore, special attention should be paid to the large-scale electric machinery on the street lighting branch network. It is best to monitor the fluctuation range of the power grid or the power supply of the separate grid transformer.

9, the line frequently trips

The lamps on the same branch are connected too much, resulting in overloading of the load on one phase and uneven distribution of power between the phases, causing the lines to trip frequently.

10, drive cooling

When the drive is installed in a non-ventilated environment, the drive housing should be in contact with the lamp housing as much as possible. If possible, apply thermal conductive adhesive or thermal pad on the contact surface between the outer casing and the lamp housing to improve the heat dissipation performance of the driver, thus ensuring the driver's Life and reliability.

In summary, the LED driver has many details to be aware of in practical applications. Many problems need to be analyzed and adjusted in advance to avoid unnecessary failures and losses!

LED  Spot light we used is Sanan chip, and the driver we used is our brand. It is made by plastic frame and  aluminum back cover. We are the manufacturer of producing energy saving interior lighting. There are three adjustable color temperatures with cool white, warm white and natural white of down lights. What's more,  it is adjustable among the three colors Red/Blue/Green/Pink. The unique feature of led Slim Panel Light is: CRI>80, PF>0.5. These panels are mainly apply to store, plaza, mall, supermarket, counter, display window, show room Counter, museum lighting.

LED Spot Light

Commercial Electric LED Downlight,Aluminum LED COB Downlight,Super Bright Ajustable Downlight Polished

Jiangmen Lika Lighting Electrical Appliances Co., Ltd , https://www.lika-led.com